Lift & Escalator Fault Reporting and Monitoring System

In most cases, elevator breakdowns are the result of users’ feedback. From detection to feedback and acknowledgement of the matter, there is already a time lag, resulting in anxiety and inconvenience. At times, even users’ feedback may be inaccurate. When the matter is finally resolved after on site inspection, testing and remedial work, time and labour cost have been incurred.

The Model WT-1010LM avoids such inconveniences and unnecessary delays. With the Model WT-1010LM supported by a sophisticated software detection system, it will monitor the performance of elevator systems like clockwork with efficiency. With the system in place, it is able to monitor the performance of 500 elevators simultaneously.

                                           

The monitoring centre is alerted of any operational anomaly and/or failure before the

end user is aware of the occurrence.

The detection and alert is reported and shown on monitoring screens on computers and via mobile message alerts. The cause of anomaly and/or failure is diagnosed upon detection and confirmation of fault. The system performs a self diagnosis to determine the extent of the fault before feedback is provided to its monitoring base.

Once the extent of fault or failure is confirmed, the monitoring centre personnel in charge has the authority to initiate corrective action such as resetting of the ELCB by turning off and turning on the main power or shut down the elevator system for safety purposes. All these from a remote location via computer interface or via a mobile device as and when deemed fit according to circumstances. A specialist team is despatched on site only when remote access remedial action have not been able to resolve the matter satisfactorily.

Of worthy note is the step by step self-diagnosis ability in the software that eliminates cases of where false alarms are given as a result of pranks and misuse. These often result in specialist teams being sent over at considerable cost only to realise that a false alarm was transmitted because someone decided to play a prank or from deliberate misuse.

For routine performance monitoring, the system is able to chart the total number of times a particular elevator unit ascends or descends its shaft in order to chart an ideal capacity load and optimise its performance based on routine patterns of usage.

Ultimately, the remote monitoring system allows for maximisation of up time, minimising down time while allocating time slots for scheduled maintenance work through an intelligent self diagnosis and appropriate first level responses to genuine faults via remote locations.

It can monitor up to 2 digital inputs. A pre-programmed alarm message can be sent to the pre-programmed phone number when lift failure. The user can also interrogate the inputs through SMS messaging.

It can also be used to monitor the daily operation of lift by counting how many times the lift goes up or down. It is prepared to count pulses of DC=70 ms and T=1.16.

The WT-1010LM also has 2 heavy-duty relay outputs which can be used to reset the lift or set off an audible alarm when lift failure. Output Relay 1 can be permanently switched ON or OFF by calling its phone number, there is no call charges incurred when dialing the unit as it will recognize an authorized telephone number calling it and reject the call without answering. Output Relay 2 can be programmed to switch on for a pre-determined length of time by sending the

Features:

·        Support Dual-Band or Quad-Band GSM network

·        2 digital inputs and 2 relay outputs

·        Programming can be done by PC (software) or SMS (remotely)

·        Monitoring by SMS mobile phone or Software

·        Alert notification via SMS (up to 8 telephone numbers)

·        Send pre-programmed SMS when lift failure

·        Able to monitor up to 500 units with software monitoring

·        Reset lift (Output Relay 1) can be done by phone call (No call charges incurred)

·        Digital alarm inputs can be used to count pulses (Monitor lift daily operation) or activates the output relay (Set off an audible alarm)

·        Backup Lithium rechargeable battery

GSM Control Switch as GSM Gate Opener (Model: WT-9003)

Use Your Mobile Phone to open your gate, garages and electric door

Let your cellular phone act as a universal remote control, open and close your automatic gate, garages, electric door, roller shutter using your mobile phone.

A lot peoples ask me, since automatic gate having remote control, why you need your mobile phone to become remote control?

Usually, when you install your automatic gate, the gate installer will gives you 2 remote controls. If your family member more than 2, you have to purchase additional remote control which will cost you more than USD 10 per piece.

The worst is if you lost or misplace the remote control, each time you have to collect back all the remote control from all family members and spend few hundreds to purchase and reprogram the new remote control.  It is really wasting a lot of money and troublesome.  Stop spending money to provide everyone with a remote control. Let them use their mobile phone as a universal remote.

Basic concept is simple, insert a SIM card into GSM control switch or GSM controller,  connect the GSM door opener to your automatic gate, garages, electric door, and program family cellular numbers inside the unit. When user calls to the unit, the GSM gate opener will check the calling number if inside the white list. If the numbers are in the list then it will reject the call and open the gate. The system did not answer the call; it simply checks the caller ID.

All electric gates have a button that is used to open them. The GSM gate or GSM door opener has a relay whose contact connected to the opening button. When user calls into the GSM control switch, the system is intelligent to search his/her numbers under its white list. If the numbers registered in list, the GSM gate controller or GSM door opener will trigger the relay and open the gate.

GSM operators did not charge anything because the system just simply rejects the call. It won’t cost anything to open the gate via the gsm gate controller or gsm door opener. Of course, an active SIM card is needed for this solution. Absolutely no call cost to open the gate.

Flexibility - You can store and delete number into the GSM controller or gate remote opener anytime. Simple sending the SMS that starts with password to the GSM gate opener.  This solution only allows the person who knows the password can insert or delete the phone numbers via text messages. If you compared to remote control, the only solution is to send back to the installer to reprogram the landing code.

GSM controller or GSM remote opener does not have limitations like a normal remote control. Using a mobile phone you can open / close from very far away, even from another city. It is really convenient to arrive in front of your house when the gate is already open, without having waiting in the middle of the road.

Crimes such as kidnappings, vehicles theft, and armed robberies normally occur while waiting at the automatic gate to open. I feel more safety with this new solution. So, why want to be a victim? Prevention is always better than cure.

The GSM control Switch also suitable for shop roller shutter or electric door. If every morning, you  has to wake up early and spend minutes and hours in the traffic jam just to hand over the keys to your workers, you can  installed one unit GSM door opener in the roller shutter or electric door, all the problem will solved. 

Every morning, you don’t need to jam in the traffic just for the sick of open the roller shutter for you staffs.  When workers arrive to the shop, they just call you. Then you call to the roller shutter or electric door, the gsm gate opener or gsm gate controller will triggers the shutter button, the shutter will open.  So convenience and save a lot of time in the travelling and petrol. Your workers also will not late to work because they need to call you every morning to reporting to work and open the roller shutter

We have experience with a mining factory. They have more than 100 transporters. Every time, any workers resigned from the company, they have to collect back 400 remotes control and re-program the landing code. This is to prevent the workers duplicate the remote and illegal transport the materials.  The GSM control switch or gate remote opener helps them to solve this problem. They just need to install one unit gate controller at the barriers. When the lorry driver at the barriers, they just need to call to the barriers and drive straight in. They can just simply delete or add the phone number into the white list.

Everybody have mobile phone now, utilized what you have in your hand to create convenience for yourself and family. Use your mobile phone to open your gate, roller shutter, garages, and electric door without any cost. You can save a lot of money, travelling times, more safety and convenience when use this GSM gate controller or gsm remote opener .  No matter if you change your car, or if you have different gates to open, your phone will always be with you all the times

For more details, please refer to http://www.witura.com/products/remote-monitoring-and-control-and-data-collection-system/gsm-switch/gsm-switch-as-gsm-gate-opener.html or write to sales@witura.com

WT-1010C2 GSM Terminal Use As Backup For Landline In The Alarm System

Usually, the alarm panel in the market will use telephone line (landline) as the main alarm communicators to sent the alarm signal to the police, house owner, center monitoring station if any alarm trigger because of intruded or sabotage.

Witura’s WT-1010C2 GSM alarm backup system can connect to any panel likes Texecom, Pyronix, Securit as the alarm backup. If any landline is been cut by intruder or faulty, the gsmdialleror alarm communicators must be intelligent enough to identified the line cut and sent out the alarm signal to the police, house owner and alarm receiving center (ARC)   - As the backup alarm

This GSM communicator is important to use in the places likes Banking, ATM machines, jewelry shop, notebook house and etc where double protection on properties is required

The cellular backup WT-1010C2 alarm communicators or GSM dialler inbuilt the audible data transferring protocols likes Contact ID, SIA, ADEMCO into the unit and ensure all the security protocol format can be transmitted to the center monitoring station.

The ideas for the for the GSM communicator or backup alarmshould perform the following ;

Use as the telephone line backup in alarm system - Phone lines can easily be cut off during storms, construction work, accidents, or even deliberate tampering by intruders. GSM Cellular or GSM module for alarm WT-1010C2 will checks the status of the telecom line in the alarm panels likes Paradox, DSC, Honeywell and in case the telecom line become unavailable, the GSM module for alarm -  WT-1010C2 will transmit the alarm using GSM to the alarm receiving center (ARC) or Center Monitoring Station (CMS)

The unit should have standby recharger battery to prevent power failure or electricity cut off by intruded. The GSM will function as normal when no electricity supply. LCD display to check the GSM signal strange and battery capacity

Auto self-check and restart function is important: The unit should continuously monitor the system status of its own. When there is a problem with the SIM card or the backup alarm is not working properly, it will automatically restart the system.

The GSM module for alarm should automatically call to 8 pre-program phone numbers while alarming. The gsmdiallershould SMS to 8 programmable cell phone number to notify the user that the PSTN line has been cut off or unavailable

In order prevent professional thief tries to disconnect GSM by using “GSM Jammer”, WT1010C2 gsm alarm backup will transmit the contact ID using telecom line if GSM signal drop immediately and trigger the siren.

The unit should also be low power consumption –GSM communicator or GSM module for alarm uses 30mA while in idle state and 260mA when transmitting an alarm to prevent backup battery finish.

Auto Test Reporting System is important - After the programmed reporting time, the cellular backup WT-1010C2 GSM Cellular should dial the programmable center station number. Once the call is connected, it will transmit the programmable contact-id to the central station and hang up. This function is to make sure that “GSM alive” daily and able to report to ARC if any emergency.

Programmable Contact ID – The cellular backup WT-1010C2 GSM dialerhas built-in alarm inputs that allow the unit to send additional signals (with user programmable Contact-ID event) to the monitoring station. Supported Protocol Pager message (DTMF no handshake)

Three Remote Controlling Outputs in the GSM module for alarm - These open collector outputs (that can sink max 300MA per output) can be turned on and off remotely through a SMS. You can use them to pull to ground your inputs. Remote control alarm communicators will be reachable by sending a SMS with a certain command. For example, switch on lighting, air conditional, or switch off generator, sensor using your mobile phone.

Three Digital Inputs - The system has the function to send alert message to the user in the event of input triggered at GSM module for alarm. For example, Zone 4 connected to an electrical door, when there is intruder or electrical door is open illegally, GSM Cellular WT-1010C2 alarm backup will receive short circuit impulse on Zone 4 and automatically send a signal to the monitoring station and notify the owner. It is possible to enable or disable the function by sending the SMS command to the unit.

Input alarm message can be edited and programmed up to 50 characters long. You can use this function to program any languages. You can change the displayed text by sending a command by SMS to the GSM communicators.

Permanent +V Output Facility – This output is available and ground on the main board of the GSM cellular. The output voltage is according to power supply and it can be used to power on other facility or device.

Wall mounting enclosure available: The GSM Cellular WT-1010C2 backup alarm units can be installed inside the alarm panel or inside its own wall mount enclosure.

Read more about us and discover the amazing array of our products. For more information please visit us at http://www.witura.com/products/security-industry/gsm-terminal-use-as-backup-for-landline-in-the-alarm-system.html

 Those interested in contacting with the Witura and want to know more information about the WT-10101C2 can also email to sales@witura.com

External Power Bank For IPHONE, IPAD, Samsung Mobile, Smartphones

Direct offer from Factory.

Witura involved in design and manufacturing external power bank for Iphone, Ipad, Samsung mobiles, smart phone , MP3, MP4, PSP and GPS.

We hope that we can work with you to promote this product into your local market  

Specification
Input/Output: Input: DC 5V, 1.0A Output: 5V, 1.0A
Compatibility: iPhone 5, iPhone 4S/4, iPad, Sumsung, Notes, Smartphone, MP3/4, PSP

Package Include:   Power Bank/7 Connectors /a Retractable USB Cable/
Warranty:1 year

Capacity:

1.      2000mAh     : USD    6.50  

2.      4400mAh     : USD  12.50

3.      5600mAh     : USD  16.00

4.      8800mAh     :  USD  20.00

5.      10,000mAh :  USD 24.00

6.      20,000mAh  : USD  27.00

The above did not include the shipping cost to your office yet. Please contact us for details shipping cost. This is because shipping to different country have different shipping cost 

We have stocks, we can deliver immediately after receive your order. Usually courier service will take 4 -6 days deliver to your office

In the even if you need any further details or product information, please feel free to contact us  - sales@witura.com

If you need more information for the product, please visit us at http://www.witura.com/other-accessories/external-power-bank.html

Please feel free talk to us online at ;

Skype  : william04

Facebook : http://www.facebook.com/witura.gsm

Turn External Power Bank for Smartphones to become Promotion Gifts

Battery life on smartphones is generally terrible and everyone knows it. Basically, it won’t last a day even with very light email user or no phone call.  Especially the heavy users, if you continuous use it for internet browsing, reply emails, messenger, it will not last for few hours.

Most of your customers having smartphones, can we help them to overcome this problem, create convenience for them and turn this problem into business opportunity ?

Witura is the manufacturing company for external power bank for Iphone, Samsung mobiles or any smart phones.

We are able manufacturing the external power bank within your budget for your customers. You can select any sharps, sizes and battery capacity for your customers. We will depend on your demand and specially design and produce the external power bank according to your budget 

Our job will included silkscreen your company logo, packing according to your request and give warranty to your end customers. We also provide specially design feature and product corporate colour selection.  

Introduction

Now, with the external power bank for Iphone, Ipad, Samsung phone, you can boost your tablet’s battery—anywhere. Portable, slim and lightweight, the WT-880 is the perfect way to ensure your battery won’t run out when you’re on the go. With 8000 mAh of power and two power ports, you can charge two devices at the same time. Net weight 220g only and cycle life 500 times. It has the capacity to full fully charge a cell phone four times or a smartphone twice or to partially charge a tablet.

Two cables are included for charging up to two devices simultaneously and recharging the Power Pack. To charge, simply plug into your device and plug the USB into the Power Pack. A convenient charge indicator lets you know how much power is available. When it’s time to recharge, just flip the cable and plug it into power source.

Features:

* With two USB output port,,it can charge two devices at the same time .

* LED display the charge state.

* Safety：over-charge protection; over-discharge protection、over-load protection; shortage protection.

* Designed to provide power for your iPhone, iPad, iPod and mobile phones.

* Built-in  8000Ah high capacity rechargeable Li-Ion battery.

* 8000mAh capability, powerful with long operation time.

* With 8 connectors, be compatible with most iPhone, iPad, iPod and mobile   phones..

* Double USB output, more convenient.

* High efficiency of power conversion.

* Electricity-saving function.

* With LED power indicator.

* Press the centre button to charge and press it again stop charging.

* Partable, practical and long cycle life.

* Safe and reliable, perfect for using on travelling and outdoor activities

Detailed Product Description:

1. Capacity:8000mah

2. N/W:220g

3. Cycle life: 500times

Product characteristics:

1).Rechargeable up to 500 times

2).Long life battery:>80% capacity after 3 year general usage

3).Power output safety design, for protecting user devices

4).LED light indicates power capacity level exactly

5).plastic casing

6).Including AC adapter

7).Protect functions: Short circuit, over-current, over-charging and over-discharging

8). Double outputs: can charge two devices at same time. 

WE EXPORT WORLDWIDE
Contact Us : www.witura.com
Email : sales@witura.com