Usually, the alarm panel in the market will use telephone line
(landline) as the main alarm communicators to sent the alarm signal to the
police, house owner, center monitoring station if any alarm trigger because of
intruded or sabotage.
Witura’s WT-1010C2 GSM alarm backup system can connect to any panel
likes Texecom, Pyronix, Securit as the alarm backup. If any landline is been
cut by intruder or faulty, the gsmdialleror alarm communicators must be
intelligent enough to identified the line cut and sent out the alarm signal to
the police, house owner and alarm receiving center (ARC) - As the backup alarm
This GSM communicator is important to use in the places likes
Banking, ATM machines, jewelry shop, notebook house and etc where double
protection on properties is required
The cellular backup WT-1010C2 alarm communicators or GSM dialler
inbuilt the audible data transferring protocols likes Contact ID, SIA, ADEMCO
into the unit and ensure all the security protocol format can be transmitted to
the center monitoring station.
The ideas for the for
the GSM communicator or backup alarmshould perform the following ;
Use as the telephone line backup in alarm system - Phone lines can
easily be cut off during storms, construction work, accidents, or even deliberate
tampering by intruders. GSM Cellular or GSM module for alarm WT-1010C2 will
checks the status of the telecom line in the alarm panels likes Paradox, DSC,
Honeywell and in case the telecom line become unavailable, the GSM module for
alarm - WT-1010C2 will transmit the
alarm using GSM to the alarm receiving center (ARC) or Center Monitoring
Station (CMS)
The unit should have standby recharger battery to prevent power
failure or electricity cut off by intruded. The GSM will function as normal
when no electricity supply. LCD display to check the GSM signal strange and
battery capacity
Auto self-check and restart function is important: The unit should
continuously monitor the system status of its own. When there is a problem with
the SIM card or the backup alarm is not working properly, it will automatically
restart the system.
The GSM module for alarm should automatically call to 8 pre-program
phone numbers while alarming. The gsmdiallershould SMS to 8 programmable cell
phone number to notify the user that the PSTN line has been cut off or
unavailable
In order prevent professional thief tries to disconnect GSM by using
“GSM Jammer”, WT1010C2 gsm alarm backup will transmit the contact ID using
telecom line if GSM signal drop immediately and trigger the siren.
The unit should also be low power consumption –GSM communicator or
GSM module for alarm uses 30mA while in idle state and 260mA when transmitting
an alarm to prevent backup battery finish.
Auto Test Reporting System is important - After the programmed
reporting time, the cellular backup WT-1010C2 GSM Cellular should dial the
programmable center station number. Once the call is connected, it will
transmit the programmable contact-id to the central station and hang up. This
function is to make sure that “GSM alive” daily and able to report to ARC if
any emergency.
Programmable Contact ID – The cellular backup WT-1010C2 GSM dialerhas built-in alarm
inputs that allow the unit to send additional signals (with user programmable
Contact-ID event) to the monitoring station. Supported Protocol Pager message
(DTMF no handshake)
Three Remote Controlling Outputs in the GSM module for alarm - These
open collector outputs (that can sink max 300MA per output) can be turned on
and off remotely through a SMS. You can use them to pull to ground your inputs.
Remote control alarm communicators will be reachable by sending a SMS with a
certain command. For example, switch on lighting, air conditional, or switch
off generator, sensor using your mobile phone.
Three Digital Inputs - The system has the function to send alert
message to the user in the event of input triggered at GSM module for alarm.
For example, Zone 4 connected to an electrical door, when there is intruder or electrical
door is open illegally, GSM Cellular WT-1010C2 alarm backup will receive short
circuit impulse on Zone 4 and automatically send a signal to the monitoring
station and notify the owner. It is possible to enable or disable the function
by sending the SMS command to the unit.
Input alarm message can be edited and programmed up to 50 characters
long. You can use this function to program any languages. You can change the
displayed text by sending a command by SMS to the GSM communicators.
Permanent +V Output Facility – This output is available and ground
on the main board of the GSM cellular. The output voltage is according to power
supply and it can be used to power on other facility or device.
Wall mounting enclosure available: The GSM Cellular WT-1010C2backup alarmunits can be installed
inside the alarm panel or inside its own wall mount enclosure.
Read more about us and discover the amazing
array of our products. For more information please visit us at http://www.witura.com/products/security-industry/gsm-terminal-use-as-backup-for-landline-in-the-alarm-system.html
Those interested in contacting with
the Witura and want to know more information about the WT-10101C2 can also
email to sales@witura.com
No comments:
Post a Comment